Quick Summary for Homeowners
- Rainwater enters through the outer weathering layer (tiles, slates, leadwork, or valleys) — stopping it from the inside never keeps the roof structure dry.
- Spray foam and internal bitumen paints hold moisture against rafters and battens, speeding up wet rot and causing trouble with home surveys.
- Drips inside your loft often show up several metres lower than the actual fault on the roof slope.
- A proper fix means inspecting and repairing the roof from the outside so water sheds straight into the gutter as intended.
Why Internal Sealants and Spray Foam Make Leaks Worse
When water starts dripping onto loft insulation during heavy rain, it is tempting to reach for a tin of roof sealant, a roll of self-adhesive flashing tape, or a can of expanding foam. We see this most weeks when we are called out to roofs around Kent. Unfortunately, every one of those internal shortcuts creates a bigger headache than the original drip.
Your tiles or slates are the first line of defence, and the felt or breathable membrane underneath is only a secondary barrier. If water is getting past the tiles and running onto the felt, it has already breached the outside of the roof. Sealing a tear from inside the loft does not stop rain getting under the tiles — it just dams the water up behind the patch until it spills over sideways onto a timber batten or runs down a rafter.
Spray foam is even worse. Once foam is squirted against the underside of old felt or directly onto the backs of roof tiles, it blocks air flow around the roof timbers and holds dampness right against the wood. Battens rot out of sight, tiles get glued together so a single broken tile can no longer be lifted out and replaced, and mortgage lenders regularly refuse loans on properties with sprayed loft foam because surveyors cannot inspect the timbers underneath.
Why the Drip Inside Rarely Matches the Hole Outside
One of the biggest reasons DIY loft repairs fail is that water travels before it drops. Rain might get in through a perished lead apron around a chimney stack or a cracked tile near the ridge, trickle down the top surface of the roofing felt for three or four metres, hit a nail hole or a sagging lap in the felt, and then run down a rafter until it finally stains your bedroom ceiling.
If you climb into the loft and patch the wet timber right above the ceiling stain, the real entry point higher up the slope stays wide open. Next time the wind drives rain from that direction, the water simply finds another route down the slope.
How Roofers Trace a Leak From the Outside
When we attend a leak with our Canterbury roof repair team, we start in the loft for two minutes just to see roughly which elevation and height the water is coming down. After that, all the real diagnostic work happens outside on the roof. Here is what we check from top to bottom:
Slipped or Frost-Cracked Tiles
A single broken nib or rusted nail lets a tile drop an inch out of line. Hairline frost cracks in older clay tiles are almost invisible from the garden, so we lift surrounding courses to check the felt underneath for wet tracks.
Perished Lead Flashing & Chimneys
Splits in lead aprons, lifted step flashing where a roof meets a wall or chimney, and cracked mortar fillets are top culprits. Water sneaks behind the lead and runs straight down the chimney breast or loft timbers.
Blocked or Cracked Valley Gutters
Where two roof slopes meet, moss and wet leaves pile up in the valley channel. In heavy downpours, dammed-up water backs up sideways under the cut tiles, or escapes through splits in old lead and fibreglass valleys.
Ridge Mortar & Eaves Felt
Cracked sand-and-cement bedding under ridge tiles lets driving rain straight into the apex. At the bottom of the slope, old bituminous felt often rots away right behind the fascia, sending water down the wall cavity.
When a Simple Repair Is Enough vs Replacing the Slope
Most roof leaks do not need a new roof. If the tiles and battens are generally sound and the leak comes from a couple of slipped tiles, a split lead flashing, or failed pointing on a ridge, a straightforward exterior repair will sort it cleanly. On a standard two-storey house where we can work off a roof ladder, that kind of repair is often wrapped up in half a day.
What pushes a job into a bigger repair or partial re-roof is usually what we find once the tiles are lifted. If old black felt has gone brittle and tears like wet paper whenever you touch it, or if galvanised nails have corroded across the whole slope ("nail sickness"), patching one square metre is false economy because the next gale will lift tiles two metres further along.
Cost is mainly driven by safe access and the scale of the strip-back. A straightforward tile or flashing repair off ladders costs a fraction of a job that needs full scaffolding over a conservatory or onto a public path. Where scaffold or a waste skip has to sit on the road or pavement rather than a private driveway, a Kent highways skip and scaffold licence will also be needed before work starts.
Under the Planning Portal rules for work to an existing roof, repairing or re-covering a roof does not normally need a building control application if less than 25 per cent of the total building envelope (walls, floor, roof, windows, doors, roof windows and rooflights) is affected and less than 50 per cent of the roof is affected. Approval is needed if you exceed either limit (the insulation may then need upgrading), make structural alterations, use a covering that performs significantly differently in a fire, or add 15 per cent or more to the weight of the covering. Isolated repairs under those limits do not normally need an application: we fix the fault, match the tiles or leadwork, and leave the gutters clear.
What to Do While You Wait for a Roofer
If rain is actively coming through right now, do not climb onto wet tiles or try to seal the loft with foam. Instead, take these practical steps inside to limit water damage until we can inspect the outside safely:
- Catch the water safely: Put a plastic tub or bucket on a wooden board spanning two ceiling joists (never rest a heavy bucket directly on plasterboard).
- Clear stored items away: Move cardboard boxes, clothes, and electrical items clear of the damp patch and pull wet loft insulation slightly aside so the plasterboard beneath can dry out.
- Check for bulging ceilings: If plasterboard is sagging with trapped water above a room, carefully pierce a small hole at the lowest point with a screwdriver over a bucket so the water drains cleanly instead of bringing the whole ceiling down.
- Take a photo from the ground: If you can see a slipped tile, displaced ridge, or hanging flashing from the garden in daylight, snap a quick photo — it helps us bring the right replacement tiles and ladders straight away.